Viton® Lathe Cut Washers

Viton® lathe cut washers handle the chemical and thermal extremes that demand a fluorocarbon elastomer, in thicknesses and edge profiles that die cutting cannot deliver. Cannon Gasket lathe cuts custom Viton washers from extruded FKM tube for aerospace fuel systems, chemical processing, semiconductor equipment, and oil and gas service.

Durometer
60A to 90A
Highlight
Broadest chemical resistance
Request a Quote909.355.1547
Custom Viton / FKM lathe-cut washers from Cannon Gasket
Get pricing

Request a quote for Viton / FKM lathe cut washers.

Properties of Viton / FKM lathe cut washers

Cannon Gasket cuts Viton / FKM lathe cut washers to your drawing in durometer and thickness specifications of 60A to 90A Shore hardness. Broadest chemical resistance of any elastomer, fuels, acids, oils, aromatics, chlorinated solvents, and hydraulic fluids. Not recommended for ketones, esters, or amines.

Viton / FKM tolerances and customization

Standard dimensional tolerances on Viton / FKM lathe cut washers land around ±0.010" to ±0.015" on OD and ID, depending on material durometer and thickness. Tighter tolerances are available on selected grades. Cannon Gasket cuts Viton / FKM to custom profiles in-house and matches lead times to your production volume. PSA backing, pad printing, custom packaging, and kitting are all on the menu when you need them.

Viton Material Notes

- Service temperature -15°F to +400°F. - Broadest chemical resistance in the standard elastomer lineup. - Lower compression set than Buna-N over long service life.

Common Applications

Aviation fuel system bolt seals, chemical processing equipment, semiconductor process valves, oil and gas exploration hardware.

Available grades

Offered in Commercial Grade, High Grade, Extreme Viton®, and FDA grades. Highly resistant to swelling when exposed to gasoline and resistant to deterioration from UV and ozone exposure.

Manufacturing, finishing & stocking

Precision & tooling: Capable of holding tolerances as tight as ±.001" on critical dimensions when required, beyond the ±0.010" to ±0.015" standard. Short- and long-run capabilities, with an extensive in-house tooling inventory for rapid turnaround.

Clean room: Cannon Gasket offers clean-environment stamping for medical, FDA, electronic, and scientific applications where a controlled level of particulate is required, with capabilities to meet ISO Class 10,000.

Stocking agreements: Blanket orders, VMI (vendor-managed inventory), JIT (just-in-time), and Kanban replenishment programs.

Pad printing: Pad print your part number, identification marking, or company name in a range of ink colors. Marking per customer specifications or MIL-STD-130.

Packaging: Parts are bagged and tagged in specified quantities and labeled with P/N or any required information. Capability to meet specific packaging and labeling requirements.

Request a QuoteViton / FKM Lathe Cut WashersDownload PDFPrint-ready spec sheetClaude SkillExpert prompt .md
Key Properties
  • Durometer: 60–90 Shore A
  • Broadest chemical resistance
  • Fuel & acid resistant
  • Excellent heat resistance
Engineering Tools
Applications
Ready to quote?
Submit your drawing or specifications and we'll respond with pricing and lead times.
Request a Quote
or call 909.355.1547
Keep Exploring

Related products, materials & reading.

Material
Buna-N / Nitrile Lathe Cut Washers
Buna-N nitrile (NBR) lathe cut washers with oil, fuel, and grease resistance.
Material
EPDM Lathe Cut Washers
EPDM lathe cut washers with superior weather, ozone, and UV resistance.
Product
O-Rings
Standard and custom O-rings in every major elastomer family.
Article
Lathe Cut vs O-Ring, Here's the Deal
When a lathe-cut seal outperforms a molded O-ring, and vice versa.
Frequently Asked Questions

Common Viton / FKM questions.

Are you ISO 9001 certified?
Yes, ISO 9001:2015 certified. Documented quality management covers incoming material verification, in-process inspection, calibrated measurement, final inspection, non-conformance handling, corrective action, and full lot traceability. AS9100-ready for aerospace, with MIL-spec and FDA 21 CFR 177.2600 / USP Class VI grades available on request.
What is a lathe-cut O-ring?
A lathe-cut seal is turned from tube stock instead of molded. Square cross-section instead of round. Lower tooling cost and often better dimensional stability than molded O-rings at low-to-mid volume. See /lathe-cut-washers/ for details.
What tolerances can you hold on lathe-cut parts?
Standard OD/ID tolerance is ±0.010 inch to ±0.015 inch, with thickness held to ±0.002 inch. We can hold ±0.005 inch on ID and OD on select compounds, and as tight as ±.001 inch on critical dimensions, with first-article inspection.
When should I specify a lathe-cut washer instead of a molded O-ring?
Lower tooling cost on short runs, tighter dimensional control on thickness, and flat sealing faces that help on grooved or machined seats. Molded O-rings are still cheaper at high volume in a standard AS568 size.
Which compounds can you lathe-cut?
Any material supplied as extruded tube: Buna-N, EPDM, Silicone, Viton, Neoprene, SBR, and specialty compounds like Fluorosilicone or Aflas. PTFE and other fluoropolymers on request.
How fast do you return a quote?
Most RFQs come back within one business day. Simple profile updates to an existing tool quote same-day. Send a drawing, DXF, or competing part number and our engineering team reviews material, tolerance, and volume before pricing.
What is the minimum order quantity?
Minimums depend on the part and material. We cut prototype and first-article quantities for engineering evaluation, then scale up to production volumes from the same tooling. For high-volume programs we run JIT, VMI, and Kanban replenishment out of Fontana, California.
What should I send with an RFQ?
Ideal: a drawing or DXF, material spec (or compound family), estimated annual volume, and any regulatory callouts (FDA, USP Class VI, AS9100, MIL-spec). If you only have a sample or a part number from a competing supplier, send that and we will reverse-engineer the spec before quoting.
What are typical lead times?
Prototype and first-article parts usually ship in 5-10 business days. Production runs from existing tooling are 2-3 weeks depending on volume and material lead time. Rush and expedite options available on a case-by-case basis.
Need custom Viton / FKM lathe cut washers?
Precision-machined from extruded tubing to your exact specifications.
Request a QuoteContact Us
ISO 9001 CertifiedAS9100-ReadyMIL-Spec CompatibleFDA / USP Class VIEst. 1971ISO 9001 CertifiedAS9100-ReadyMIL-Spec CompatibleFDA / USP Class VIEst. 1971ISO 9001 CertifiedAS9100-ReadyMIL-Spec CompatibleFDA / USP Class VIEst. 1971ISO 9001 CertifiedAS9100-ReadyMIL-Spec CompatibleFDA / USP Class VIEst. 1971